|
|
|
|
|
|
Transient Suppression Module
|
Our Price: $86.00
|
|
|
This transient suppression and reverse polarity protection module is designed to limit the voltage and current that can be applied to equipment connected to its output terminals. The AC power line or bipolar low voltage DC models will provide symmetrical clamping in both directions. The single polarity low voltage DC models differ in that they will clamp the applied reverse voltage to less then 2 volts. All of the models contain fast acting fuses for short circuit protection.
|
|
|
|
|
|
|
|
|
|
Signal Relay Interface Module
|
|
Our Price: $150.00
|
|
|
This series of relay interface modules are designed to be applied to a wide selection of general purpose signal switching applications. They are available with either two or four form C contacts. In addition, most models are offered with optional coil transient suppressors and indicator lamps. The relay is plugged into a molded, phenolic socket on the circuit board with the contacts and coil connections terminated to heavy duty barrier type terminal blocks. The relay is secured in the socket with a steel hold down spring.
|
|
|
|
|
|
|
|
|
|
Power Relay Interface Module
|
|
Our Price: $150.00
|
|
|
This series of power relay interface modules are designed to be applied to a wide selection of general purpose switching applications. They are available with either one or two form C contacts rated for five or ten amps. Most models are available with the optional coil status indicator lamps and transient suppressors. The relay is plugged into a molded, phenolic, standard octal socket on the circuit board with the contacts and coil connections terminated to heavy duty barrier type terminal blocks.
|
|
|
|
|
|
|
|
|
|
Linear DC Voltage Regulator
|
|
Our Price: $157.00
|
|
|
This linear voltage regulator assembly is designed to convert the input DC power line to a stable, lower voltage, unipolar DC output. Models are available to provide a selection of output voltages from 5 to 24 volts DC to the connected load. Both positive or negative output voltage configurations are available. The positive 5 volt output model is capable of supplying a maximum of 3 amps to the connected load. Other voltage configurations will deliver up to 1 amp to the connected load. This device is typically used with an unregulated dc source to provide a stable power supply for transducers and other electronic devices that do not include internal voltage regulators.
|
|
|
|
|
|
|
|
|
|
Current to Voltage Converter, 4 to 20 ma. Input
|
|
Our Price: $235.00
|
|
|
This current to voltage converter module is designed to be used as a general purpose linear, signal level conditioner. The module will convert a 4 to 20 ma. signal into a voltage. This device should be used in unidirectional applications where the output voltage will vary from zero to maximum as the input changes from 4 to 20 ma.
|
|
|
|
|
|
|
|
|
|
Instrument Follower, Unipolar Voltage Input
|
|
Our Price: $235.00
|
|
|
This instrument follower module is designed to be used as a general purpose linear, signal level conditioner. The module will convert a voltage input signal at one level into a voltage output signal at another level. This device should be used in unidirectional applications where the controller command signal generator voltage must be converted before it is applied to the controller. A typical application uses this module to condition the signal from a tachometer that is used as the command input to follower drive.
|
|
|
|
|
|
|
|
|
|
Dither Generator Module
|
|
Our Price: $271.00
|
|
|
This dither generator module is designed to provide a bipolar triangle or square wave output for use as the dither input to high performance servovalve amplifiers. It should be used in applications where the utmost in system response and accuracy is required. In addition, it may also be used as a general purpose oscillator.
|
|
|
|
|
|
|
|
|
|
Bipolar Limit Detector Module
|
|
Our Price: $300.00
|
|
|
This bipolar limit detector module is designed to provide a relay contact transfer whenever the input signal exceeds one of the trip point settings. Separate relay outputs are supplied for the positive and negative setpoints. Once the contacts transfer, they will remain so until the input signal returns below the trigger threshold. Models are available for use with either voltage or current input signals. This module can be used in bidirectional applications to indicate a direction change or with double solenoid valves as a level controller. The differential input mode allows the module to transfer the relays based upon the absolute difference between two input signals of the same polarity.
|
|
|
|
|
|
|
|
|
|
Zero Signal Detector Module
|
|
Our Price: $330.00
|
|
|
This zero signal detector module is designed to transfer the output relay contacts at any time the input signal exceeds the trip point setting. The trip point is symmetrical around the zero point, thus the output relay will pick up at the same point for both positive and negative input signals. Once the contacts transfer, they will remain so until the input signal returns below the trigger threshold. This module can be used in bidirectional applications to monitor the output and prevent a change in direction unless the system is stopped. It is also applied to monitor a command or feedback signal and shutdown the system or notify the operator should the signal drop below the threshold point.
|
|
|
|
|
|
|
|
|
|
Bipolar Signal Scaling Module
|
|
Our Price: $379.00
|
|
|
This bipolar signal scaling module is designed to be used as a general purpose linear, bipolar gain block or signal level converter. The module can be used for current to voltage or voltage to voltage level conversion. The three input terminals allow multiple input signals be summed and scaled into a common output. The module provides both a non-inverted and inverted voltage output signal.
|
|
|
|
